-
Gokuu2008
.User deleted
RIFF JTAG - Toshiba Portege G900 Unbrick, Dead Boot repair supported
14.03.2011 Toshiba Portege G900 Unbrick, Dead Boot repair supported
Resurrection of Toshiba Portégé G900 PDA part is not hard. Battery is required for successful HALT operation. If USB Data Cable is connected phone is auto powered on when battery is inserted.
If during connect operation (“Establish communication with the phone…”) after 2-3 passes there is still no success (progress bar keeps running from 0 to 100% and so on) then remove battery and insert it again. If USB cable is not connected then press and hold Power On key.
Current resurrector re-flashes only the EBOOT and secondary EBOOT area, and will not re-write IPL area (though write of this area is supported too).
Please note: DiskOnChip G4 memory has security features, due to which there is a risk of permanently blocking the access to the flash memory while re-flashing the IPL areas. Current resurrector will not touch the IPL zone, but it is possible you’re already holding such killed device in hands. If it is so you will see this error:
************************************************** **************
Detected a Not Initialized FLASH1 Chip ID: 0×0400/0xFBFF
ERROR: Selected FLASH Chip was not initialized by the DCC Loader
************************************************** **************
This can happen due to unknown protection keys used or due to permanently blocked MDOC chip. If latter is true we advise you to solder a new flash memory chip or throw this phone away to the trash bin.
To resurrect Toshiba G900 PDA part:
Solder JTAG wires to the Toshiba G900 PDA pads;
Connect USB cable to phone and PC;
Make sure Toshiba G900 PDA is selected in the list of models;
Insert battery and click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter USB download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Left soft’ key (which is exactly above the Dial key) and press ‘Power ON’ button. In few seconds you should see red download screen.
To enter SD-card download mode:
Disconnect PC cable;
Insert battery;
Hold ‘D’ key and press ‘Power ON’ button.
Additional info:
Phone has DiskOnChip G4 memory type, which has security features. It has two password protected partitions (Password1 = 12345678, Password2 = 00000000);
IPL re-flash is not performed in this resurrector on purpose. While re-flashing the IPL area there is a risk of permanently blocking the memory chip.
Any write access (Erase or Write) on MDOC NAND memory range 0×00000000 to 0x0017FFFF is rejected by the DCC Loader. For full image writing convenience access to that range will not rise any error, data will just be ignored and reported as if it was written successfully, thus you still can write full image files using ‘Auto FullFlash Size’ checked.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
. -
The_Colombian_Team .
User deleted
RIFF BOX - ROVER PC EVO V7, MARVELL PXA3XX Generic NAND DCC Loader
21.03.2011 RoverPC EVO V7 Unbrick – Dead boot repair supported
RoverPC Evo V7 resurrection is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect RoverPC Evo V7:
Solder JTAG cable to RoverPC Evo V7 JTAG pads;
Connect USB cable to phone and PC;
Make sure RoverPC Evo V7 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original firmware downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Camera’ keys and press Power-On.
21.03.2011 MARVELL PXA3XX NAND Generic DLL Released
Resurrector PXA3XX contains only NAND DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU's internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
21.03.2011 - RIFF Box Firmware v1.21
Firmware 1.21
---------------------------
Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.
RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.. -
Gokuu2008 .
User deleted
RIFF JTAG - Samsung GT-B7330 Omnia PRO Boot Repair Supported
22.03.2011 Samsung GT-B7330 Omnia PRO Boot Repair Supported
Please start JTAG Manager and click “Check for Updates” button. You’ll be notified about new DLL, download it and restart the software.
“Samsung_B7330.dll” contains pinout, instructions and required repair files for Samsung GT-B7330 OmniaPRO Unbrick – Boot Repair.. -
ncoolsoft .
User deleted
RIFF JTAG Updates - HTC Ozone/Chief, JTAG Manager v1.29 and more
--------------------------------------------------------------------------------
31.03.2011 HTC Ozone XV6175 (HTC Chief) Unbrick, Boot Repair, Unlock, IMEI Repair, CID Update supported
Resurrecting HTC Chief is easy:
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.44.0000 SPL version.
Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘CEDA10000′.
As well, you can change CID – for this make sure ‘Repair Custom ID’ field is checked in the Resurrection Guide dialog.
To resurrect HTC Chief:
Solder JTAG cable to HTC Chief JTAG pads;
Make sure HTC Chief is selected in the list of models;
Insert battery and connect USB Cable;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
31.03.2011 JTAG Manager v1.29, RIFF Box Firmware v1.21 released
JTAG Manager 1.29
—————————
Fixed bug with plugins managing in case there is more than 1 plugin DLL available;
Currently selected plugin is remembered now and will stay on next startups;
Fixed Access Violation error during software startup in case there is none resurrector DLL present;
Added Reset Method selection feature for more precise reset operation when Custom Target Settings is active;
Updates manager & Updates tracking were completely reworked, and now are based not on the system time but on file’s hashing.
Thus since now on the JTAG Manager’s installation folder can be copied/moved/re-installed (whatever else) without need to re-download full set of files again.
(SDK): more functions are now available (exported) for future Resurrector DLLs;
Many cosmetic changes;
FINALLY: “healed” the optimized DLL loading scheme:
User shall see: “Found and Initialized: XXX New and YYY Old External Repair Pack(s)” where XXX must be always non-zero only on first startup after there were new DLLs downloaded from the support.
On following JTAG Manager startups XXX shall be always equal to zero (!!!)
For example, after downloading 3 more new DLLs while there were 100 Resurrector DLLs already installed, after JTAG Manager restarts user shall see:
Found and Initialized: 3 New and 100 Old External Repair Pack(s)
on next and all following restarts user shall see:
Found and Initialized: 0 New and 103 Old External Repair Pack(s)
Re-worked balloon hints system – Own (not windows’) balloons are shown, so no matter now what are the windows’ tray icon settings are.
Added balloon hints for cases when target is not detected, error code 0×45, Device Id = 0x000000E1.
Don’t forget that balloons hints can be switched on or off from the DCC Read/Write page – click “Notifications…” and select”For Advanced Users” page to see settings
- JTAG Manager now has new Icons www.jtagbox.com/wp-includes/i...icon_smile.gif
- Improved JTAG Manager restarting during updating itself
Firmware 1.21
—————————
Added RX-polling feature (debugger-to-target) for PXA3XX DCC transfers.
RIFF BOX firmware is able now to wait (if resurrector DLL will request so) for PXA3XX target to be ready to accept
next packet over DCC: this feature slows down a little the JTAG-to-Target DCC
transfers but guaranties no packets loss for slow clocked targets;
31.03.2011 RIFF Data Exchange Plugin 1.00 released
First release of the RIFF Data Exchange Plugin: please download it, and then select it on Usefull Plugins page in the JTAG Manager to read short description about the plugin’s abilities. In short it allows RIFF BOX users to share and use Full Image files in centralized manner without need to waste a lot of time for browsing countless forums.
Because of big sizes of Full Image files, we don’t host them, instead users share links to file sharing servers where the files are actually uploaded. (like megaupload.com, rapidshare.com and others) You can browse existent links for required image file or share your image file (by sharing a http link) to help other RIFF BOX users.
If you share image file please take attention to carefully fill file details so for other people this to be an easy task to search for required file (link)
If you used link to download file and found it good or bad or link to be broken – please Rate this link so other users see the usability of the link.
At the moment of first release of this plugin there are already few links shared so you’ll catch the idea fast.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
. -
roniscell .
User deleted
04.04.2011 HTC Advantage X7510 (HTC Athena) Unbrick – Boot Repair supported
Resurrection of HTC Athena is easy. Most convenient is to have USB cable connected and battery inserted.
If during connection progress bar in JTAG Manager keeps running from 0 to 100% press with stylus the reset button on the phone (reset button is near to the JTAG pads).
Resurrector will reflash IPL and SPL areas. You can select SPL version to be flashed in the settings window which popups before resurrection. IPL which is flashed: “ATHENA IPL DVT 2.02 H3” version.
Current resurrector works only with HTC Athena hardware revisions which have DiskOnChip H3 memory chip installed. If you have hardware revision with DiskOnChip G4 memory chip used then select different resurrector.
To resurrect HTC Athena with DiskOnChip H3:
Solder JTAG cable to HTC Athena JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure HTC Athena is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Camera’ key and press ‘Power ON’ key or use stylus to press ‘Reset’ button. In few seconds you should see TriColor picture.
Additional info:
DiskOnChip H3′s full NAND memory chip is divided into partitions by the internal memory controller. Thus DCC Loader creates virtual FLASH chip for each partition – you can read/write these partitions by selecting proper ROM index (“Access ROMi Address Space”) on the JTAG Manager’s DCC Read/Write page;
DiskOnChip H3 has no spare zones, thus only Main field must be used during write operations. ECC Enable checkbox has no meaning here.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
http://www.jtagbox.com/jtag-news/riff-jtag...pair-supported/. -
roniscell .
User deleted
RIFF JTAG - CDMA Day ! QSC1100, Micromax C111, Huawei C2830 supported
06.04.2011 CDMA QUALCOMM QSC1100 Generic DLL released
Resurrector QSC1100 X14 contains only DCC Loader, thus it is to be used only for operations on DCC Read/Write page in the JTAG Manager.
Embedded DCC Loader is designed to work inside of MCU’s internal RAM memory, thus it is not sensitive to external SDRAM configuration or availability or its physical state.
Initial H/W init sequence will setup MCU’s PLL with these parameters:
Clock Multiplier = 0×14
Since few different versions of QSC1100 resurrector may exist (with different multiplier values) you may select the one which suits best to your device
06.04.2011 CDMA Micromax C111 Boot repair supported
[/URL]
Resurrecting Micromax C111 is simple. Board is auto powered on when battery is inserted and USB cable is connected.
There are 2 different hardware revisions of this phone – one is based on Qualcomm QSC1100 MCU and other – is Qualcomm QSC6010 MCU. Current resurrector shall be selected if you have QSC1100 revision.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x6FFFFF).
To resurrect Micromax C111:
Solder JTAG cable to Micromax C111 JTAG pads;
Connect ignition cable for auto power on or use battery;
Make sure Micromax C111 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
06.04.2011 CDMA Huawei C2830 Boot repair supported
Resurrecting Huawei C2830 is simple. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board. Since the JTAG test points are placed under keyboard sticker we recommend using USB data cable to supply power to the device.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x5FFFFF).
Please note: if you do not have JIG (that is you solder wires instead) then black graphite covering has to be carefully scratched off in order to access copper surface of the pads.
To resurrect Huawei C2830:
Solder JTAG cable to Huawei C2830 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C2830 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
www.jtagbox.com/. -
roniscell .
User deleted
RIFF JTAG - Samsung S7230E Wave 723 Unbrick – Boot Repair supported
08.04.2011 Samsung S7230E Wave 723 Unbrick – Boot Repair supported
Resurrecting Samsung S7230E is easy. To power the phone connect USB cable and insert battery. In case phone is not detected de-power phone completely, then wait few seconds, insert USB cable and then insert battery.
To resurrect Samsung S7230E:
Solder JTAG cable to Samsung S7230E JTAG pads;
Connect USB cable to phone and PC;
Insert battery;
Make sure Samsung S7230E is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state. We used MultiLoader 5.64 version.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ (on the left side of phone) and ‘Lock’ (right side bottom part) keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
www.jtagbox.com/. -
roniscell .
User deleted
IFF JTAG - HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair sup
09.04.2011 HTC 7 Mozart Unbrick, Unlock, IMEI Repair, CID Repair, ModelID Repair supported
Resurrecting HTC Mozart is easy. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 0.60.1000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PD6710000′.
To resurrect HTC Mozart:
Solder JTAG cable to HTC Mozart JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Mozart is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
www.jtagbox.com/. -
ncoolsoft .
User deleted
RIFF JTAG - CDMA HTC Droid Eris, HTC Polaris and more
12.04.2011 CDMA HTC Droid Eris, Unbrick, Boot Repair, ModelID repair supported
Resurrecting HTC Droid Eris is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB0010000′.
To resurrect HTC Droid Eris:
Solder JTAG cable to HTC Droid Eris JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Droid Eris is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;
12.04.2011 HTC Polaris (HTC Cruise) Unbrick, Unlock, IMEI and CID Update, ModelID repair supported
Resurrecting HTC Polaris is easy.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 2.20.AxeBox. Additionally, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘POLA10000′.
To resurrect HTC Polaris:
Solder JTAG cable to HTC Polaris JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Polaris selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
12.04.2011 QUALCOMM NOR Generic DLL-s update:
QSC1100_X14_NOR,
QSC60XX_L18_D08_NOR,
QSC60XX_L20_D08_NOR,
QSC60XX_L24_D08_NOR
Whats new:
Added support for NOR Chips which have Intel/Sharp Extended Command Set (according to the CFI specification)
This means any NOR flash chip which is manufactured by CFI standard (it means all NOR flash chips) will be supported with above listed DLL-s. There is no need to update DCC Loaders for single flash chip ID, since configuration data are obtained from CFI.
12.04.2011 RIFF JTAG Manager v1.30, RIFF Box Firmware v1.22 released
Firmware 1.22
---------------------------
Fixed bugs in ARM7 core handling routines
JTAG Manager 1.30
---------------------------
Added DISABLE_POLLING request processing from DCC Loader
(used by DCC Loaders which have small RAM size available and there is no DCC RX polling is implemented in RIFFBOX firmware for current core);
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.. -
roniscell .
User deleted
RIFF JTAG - CDMA Samsung SCH-S109 (MSM6000) Repair supported and more !
20.04.2011 CDMA Samsung SCH-S109 (MSM6000) Repair supported
Resurrecting Samsung S109 is simple. Phone is auto powered on with charger connected; battery presence is not required.
Resurrector re-flashes only firmware zone of the phone (0×000000 to 0x3FFFFF).
To resurrect Samsung S109:
Solder JTAG cable to Samsung S109 JTAG pads;
Connect ignition cable for auto power on or use battery;
Make sure Samsung S109 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
20.04.2011 JTAG Manager v1.31, RIFF Box Firmware v1.23 released
Whats new :
JTAG Manager 1.31
“RUN/STOP” Loaders functionality is added (and alternative to the DCC Loaders)
This is required for some ARM7 cores when Debug Communication Channel (DCC) to/from core is not functional (like in MSM6000)
Firmware 1.23
Added 8/16/32-bit bus read/write access rotuines for ARM7 core
ARM7 debug is now available in ARM/Thumb modes (use the GDBServer for this);
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution. -
roniscell .
User deleted
RIFF JTAG - CDMA Motorola W150i (MSM6000) Repair supported
21.04.2011 CDMA Motorola W150i (MSM6000) Repair supported
Resurrecting Motorola W150i is simple. Phone is auto powered on with charger connected; battery presence is not required. Pin TMODE has to be connected to GND in order to enable JTAG connection.
Please note, MSM6000 draws power from JTAG pins, thus board can be detected via JTAG even without any power supplied. But for successful resurrection the power (battery or charger) is required. Thus when resurrection is complete don’t forget to disconnect phone from RIFF BOX to de-power it completely.
To resurrect Motorola W150i:
Solder JTAG cable to Motorola W150i JTAG pads;
Connect charger for auto power on or use battery;
Make sure Motorola W150i is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution. -
roniscell .
User deleted
RIFF JTAG - CDMA Haier C300 Repair supported, JTAG Manager v1.32 released
21.04.2011 CDMA Haier C300 Repair supported
Resurrecting Haier C300 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Haier C300:
Solder JTAG cable to Haier C300 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Haier C300 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
21.04.2011 JTAG Manager 1.32 released
---------------------------
Resurrector DLLs can now request current Memory Chip IDs
This is most usefull for NOR-based devices since sometimes such devices require different firmware for different NOR memory chip IDs. Thus resurrector DLLs will be able to perform automatic selection of resurrection data.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution. -
roniscell .
User deleted
RIFF JTAG - CDMA Haier C3010, LG LSP450T Repair supported
22.04.2011 CDMA Haier C3010, LG LSP450T Repair supported
Resurrecting Haier C3010 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chips with IDs 0x00EC/0x257E and 0x017E/0×2210. Proper data will be selected automatically depending on memory ID in your device.
To resurrect Haier C3010:
Solder JTAG cable to Haier C3010 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Haier C3010 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Resurrecting LG LSP450T is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0×0020/0×8867
To resurrect LG LSP450T:
Solder JTAG cable to LG LSP450T JTAG pads;
Insert USB Data cable into board and PC;
Make sure LG LSP450T is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution. -
ncoolsoft .
User deleted
RIFF JTAG - CDMA Samsung S239 (MPower) Repair supported
26.04.2011 CDMA Samsung S239 (MPower) Repair supported
Resurrecting Samsung S239 is simple. Phone is auto powered on with USB Cable connected; battery presence is not required.
To resurrect Samsung S239:
Solder JTAG cable to Samsung S239 JTAG pads;
Connect ignition cable for auto power on or use battery;
Make sure Samsung S239 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
. -
roniscell .
User deleted
03.05.2011 Samsung B2710 (Samsung Xcover 271) Unbrick / Repair supported
Samsung B2710 resurrection is simple. Phone is auto powered on when USB Cable and battery are connected.
To resurrect Samsung B2710 do this:
Solder JTAG cable to the Samsung B2710 JTAG pads;
Connect USB cable to phone and PC;
Make sure Samsung B2710 is selected in the list of models
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ’9′ keys and press Power-On. Screen lights up with Download mode message.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution.
FORO EXCLUSIVO UPDATES RIFF |
