-
ncoolsoft
.User deleted
RIFF JTAG - Samsung Nexus S, HTC Incredible C Unbrick/Boot repair supported
04.05.2011 HTC Droid Incredible ADR6300 (HTC Incredible C) Unbrick Dead Boot Repair supported
Resurrecting HTC Incredible C is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PB3120000′.
To resurrect HTC Incredible C:
Solder JTAG cable to HTC Incredible C JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Incredible C is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume down’ key and press ‘Power ON’ button to enter HBoot menu;
Hold ‘Volume up’ key and press ‘Power ON’ button to enter Recovery mode;
04.05.2011 Samsung Nexus S (i9023) Unbrick Boot repair supported
Samsung I9023 is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
Current resurrector has two different versions of primary boot loaders (PBL) embedded. This depends on hardware version of your phone which boot to use, thus in case of failure (cannot enter download mode after resurrection) of first loader try selecting another.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
To resurrect Samsung I9023:
Solder JTAG cable to Samsung I9023 JTAG pads;
Connect microUSB cable to phone and PC;
Insert battery;
Make sure Samsung I9023 is selected in the list of models;
Make sure a fixed TCK frequency is selected;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
. -
roniscell .
User deleted
07.05.2011 LG CU720 Shine Unbrick – Boot repair supported
Resurrecting LG CU720 is very hard because it requires non-beginner soldering skills (since JTAG pads on board are very small and are close to each other).
Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect LG CU720:
Solder JTAG cable to LG CU720 JTAG pads;
Insert USB Data cable into board and PC;
Make sure LG CU720 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution. -
roniscell .
User deleted
RIFF JTAG - CDMA Day Again ! 
09.05.2011 RIFF JTAG – CDMA Day Again ! More power for Indian users !
Whats new:
Added Huawei CDMA models support :
Huawei C2823 Repair, Read/Write NOR flash
Huawei C2809 Repair, Read/Write NOR flash
Huawei C2808 Repair, Read/Write NOR flash
Huawei C2807 Repair, Read/Write NOR flash
Huawei C2607 Repair, Read/Write NOR flash
Huawei C2905 Repair, Read/Write NOR flash
Added ZTE CDMA Model :
ZTE C335 Repair, Read/Write NOR flash
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution. -
.:: Saulcell ::. .
User deleted
10.05.2011 CDMA LG VM265, CDMA Huawei Broadband Modem EC1260 supported
Resurrecting LG VM265 is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect LG VM265:
Solder JTAG cable to LG VM265 JTAG pads;
Insert USB Data cable into board and PC;
Make sure LG VM265 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
Resurrecting Huawei EC1260 is simple. Just make sure you solder all JTAG signals and insert modem into a USB port for it to get powered.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
At resurrection startup you can select which zones are to be re-flashed. Thus you can save a lot of time if you know approximately which zone is damaged. Select EFS or MMC areas to be flashed only in case you are sure those are damaged – these areas quite big in size; unnecessary reflash is just a waste of time.
Please note, if you chose EFS to be repaired, an original ESN will be lost and substituted with the one contained in resurrection data. Current resurrector does not support ESN repair.
To resurrect Huawei EC1260:
Solder JTAG cable to Huawei EC1260 JTAG pads;
Insert Huawei EC1260 modem into any USB port for power;
Make sure Huawei EC1260 is selected in the list of models;
Click Resurrect button;
After Selection Dialog popup choose zones to be flashed;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.. -
ncoolsoft .
User deleted
RIFF JTAG - Samsung S5830, A867 Unbrick/Repair, Huawei Modem E5830 supported
12.05.2011 Samsung Galaxy Ace S5830 Unbrick – Boot repair supported
Samsung S5830 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.
To resurrect Samsung S5830 do this:
Solder JTAG cable to Samsung S5830 JTAG pads;
Insert battery and connect USB cable to phone and PC;
Make sure Samsung S5830 is selected in the list of models;
Click Resurrect button;
Wait few seconds until software signals a successful operation completion;
Disconnect USB cable, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On to enter Download Mode;
12.05.2011 Huawei E5830 Broadband modem Unbrick – Boot repair supported
Resurrecting Huawei E5830 is simple. Just make sure you solder all JTAG signals. Connection can be established with USB Cable connected, though in some rare cases battery presence may be required.
If modem is not detected by RIFFBOX JTAG, disconnect JTAG connector, re-insert modem into USB and then connect back the JTAG connector.
Please note, if only an USB cable is connected the device is detected by PC as unknown device. So, after resurrection in order to check if modem is alive make sure battery is connected.
To resurrect Huawei E5830:
Solder JTAG cable to Huawei E5830 JTAG pads;
Insert Huawei E5830 modem into any USB port for power;
Make sure Huawei E5830 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
12.05.2011 Samsung Eternity A867 Unbrick - Boot repair supported
The Samsung A867 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Samsung A867:
Solder JTAG cable to Samsung A867 JTAG pads;
Connect USB cable;
Make sure Samsung A867 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Down’ and ‘Camera’ keys and press ‘Power ON’ button.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
. -
ncoolsoft .
User deleted
RIFF JTAG - CDMA Huawei C5589, Dopod Magic A6188 ,Samsung Z630, Huawei E5832 added
13.05.2011 CDMA Huawei C5589 Unbrick – Boot repair supported
Resurrecting Huawei C5589 is simple. Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x017E/0×2230
To resurrect Huawei C5589:
Solder JTAG cable to Huawei C5589 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Huawei C5589 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Dopod Magic A6188 (HTC Sapp400) Unbrick, Unlock, IMEI and CID repair supported
The HTC Magic (SAPP400) is based on ESM7206A chipset. Phone is auto powered on with USB Data Cable connected to the PC while battery is connected.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.53.02000 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘SAPP*****’. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC Magic (SAPP400):
Solder JTAG cable to HTC Magic (SAPP400) JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC Magic (SAPP400) is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Back (←)’ key and press ‘Power ON’ button. In few seconds you should see download mode saying Fastboot USB.
13.05.2011 Samsung Z630 Unbrick – Boot repair supported
Resurrection of Samsung Z630 requires battery or external power supply. Most convenient way is to use additionally an USB cable: in this case power is auto powered on and there will be no need to hold power on key during connection startup.
Please note, phone will be detected even with only USB cable connected, but stable connection and stable data exchange will be achieved only when battery (or external power supply) is connected too.
To resurrect Samsung Z630:
Solder JTAG cable to Samsung Z630 JTAG pads;
Insert battery (or connect external power supply to the battery pads) and connect USB cable;
Make sure Samsung Z630 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ’4′ key and press ‘Power ON’ button. In few seconds you should see light-blue screen.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
. -
roniscell .
User deleted
RIFF JTAG - More CDMA Models, Samsung S5250 Unbrick supported
29.05.2011 More CDMA Models, Samsung S5250 Unbrick supported
New CDMA models added today :
ZTE S160
Unicare UN510BF
Unicare ChivaC2
Huawei C5100
Samsung phones :
Samsung S5250
Samsung S5260 (Bug Fix)
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution. -
jairotapia56 .
User deleted
Firmware 1.24
---------------------------
- The Most Annoying RIFF Bug (THE BUG) is Fixed Finally!!!
- During flashing operations both RIFFBOX and JTAG Manager were frozing while DATA LED was blinking constantly.. -
roniscell .
User deleted
10.06.2011 More CDMA Models, new bug fix updates today
Whats new :
CDMA Models JTAG support :
Huawei C2605
Micromax MMX 250C
ZTE WP829
LG RD3640
Bug fix updates :
Samsung S5830
HTC Incredible C
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
www.jtagbox.com/. -
.:: Papusoft ::. .
User deleted
- HTC Desire HD A9191 (HTC Ace) = Unbrick, IMEI, CID, ModelID, Simlock repair = WORLD FIRST ! ! !
Firmware 1.25
---------------------------
- added 5.0V USB Power On/Off controlling feature
- changed sequence for 32-bit write accesses for ARM11 core (MSM8xxx support)
JTAG Manager 1.33
---------------------------
- Improved connection policy:
Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages - booting stage and working stage.
Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup
by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
After "booting" stage is complete, the "working" speed is set - the one which is selected by user in the JTAG TCK Speed field.
If Booting Speed in resurrector DLL is hardcoded as 'RTCK' the JTAG Manager would always use RTCK mode during booting stage.
Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically
change booting speed to the fixed TCK too.
- fixed bug: if "Use End Address" and "AutoFull Flash Size" were checked there was error setting valid length to read.
- for Advanced Users: advanced settings are now moved from the DCC Read/Write page ("Notifications...") into separate button on Box Service page (Advanced Settings button)
- added 5.0V USB Power On/Off controlling feature
For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed,
go to "Advanced Settings" page and set desired mode for "Enable 5.0V output" checkbox.
When enabled, 5.0V power will be on after any "JTAG" operation executed and will remain "ON" until
box restart or until "Enable 5.0V output" checkbox is unchecked and any "JTAG" operation is executed.
- added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards)
- if error code 0x3C (write-protect) is received no recover attempts are made.
. -
ncoolsoft .
User deleted
RIFF JTAG - CDMA Updates again
22.06.2011 CDMA day again, 3 new models supported
Whats new:
Motorola W200 full support
Huawei C2801 full support
Nokia 1006 full support
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
Dont forget to check previous updates :
RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair « RIFF Box – JTAG Revolution,
RIFF JTAG – JTAG Manager v1.33, RIFF Box firmware v1.25 released « RIFF Box – JTAG Revolution
RIFF Box – JTAG Revolution. -
roniscell .
User deleted
RIFF JTAG - CDMA Updates again
22.06.2011 CDMA day again, 3 new models supported
Whats new:- Motorola W200 full support
- Huawei C2801 full support
- Nokia 1006 full support
Dont forget to check previous updates :
RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair « RIFF Box – JTAG Revolution,
RIFF JTAG – JTAG Manager v1.33, RIFF Box firmware v1.25 released « RIFF Box – JTAG Revolution
RIFF Box – JTAG Revolution
. -
ncoolsoft .
User deleted
RIFF JTAG - HTC Wildfire S A510E (HTC Marvel), 7 More CDMA models supported
07.07.2011 HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.
Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC WildFireS:
Solder JTAG cable to HTC WildFireS JTAG pads;
Insert USB Data cable into board and PC;
Make sure HTC WildFireS is selected in the list of models;
If you use battery, press Power On key;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.
Following CDMA models are supported from today :
Samsung B139 Repair/Unbrick, Read/Write NOR Flash
Samsung B259 Repair/Unbrick, Read/Write NOR Flash
Samsung B309 Repair/Unbrick, Read/Write NOR Flash
Samsung B319 Repair/Unbrick, Read/Write NOR Flash
Samsung B379 Repair/Unbrick, Read/Write NOR Flash
Samsung B619 Repair/Unbrick, Read/Write NOR Flash
Huawei C31 Repair, Read/Write NOR flash
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
. -
ncoolsoft .
User deleted
RIFF JTAG - Samsung T749, Samsung E189 Unbrick - Boot repair supported
The Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Samsung T749:
Solder JTAG cable to Samsung T749 JTAG pads;
Connect USB cable;
Make sure Samsung T749 is selected in the list of models;
Click Resurrect button;
Wait till software signals a successful operation completion;
Disconnect power supply, de-solder JTAG wires;
Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.
To enter download mode:
Disconnect PC cable;
Insert battery;
Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.
Resurrecting Samsung E189 is simple.
Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256
To resurrect Samsung E189:
Solder JTAG cable to Samsung E189 JTAG pads;
Insert USB Data cable into board and PC;
Make sure Samsung E189 is selected in the list of models;
Click Resurrect button;
Choose which areas to flash;
Wait till software signals a successful operation completion;
De-solder JTAG wires;
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
. -
ncoolsoft .
User deleted
RIFF JTAG - Latest Updates and News !
Here is short list of latest news :
RIFF JTAG – Qtek 9000 (HTC Universal) Unbrick – Boot repair supported « RIFF Box – JTAG Revolution
Other names for this device :
I-Mate JASJAR (HTC Universal)
Dopod 900 (HTC Universal)
O2 XDA Exec (HTC Universal)
T-Mobile MDA Pro (HTC Universal)
Orange SPV M5000 (HTC Universal)
Qtek 9000 (HTC Universal)
Grundig GR980 (HTC Universal)
Vodafone VPA IV / v1640 (HTC Universal)
Bug fix updates :
HTC_Wildfire.dll
- Added feature to flash RECOVERY and BOOT zones during resurrection.
- Added code reading option
HTC_WildfireS.dll
- By mistake was released DLL for usual HTC Wildfire model. Now is ok.
Thanks to Tatek and Basar for help. Free beers for both
Qualcomm Partition tool 1.04 :
Added support for 4kb page code reading (Applies to HTC Models)
In case You want to read unlock code from dump with 4kb page, and You get "Simlock zone is not found" message, tick "Don't adjust HTC Partition for 4kb NAND pages" check box, and read partition again.
Beta testers required for Samsung Galaxy S II :
Samsung Galaxy S2 i9100 wanted for beta test ! ! !
Support for Exynos 4210 Samsung CPU is added, and will be released after tests.
Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.
RIFF Box – JTAG Revolution
.
FORO EXCLUSIVO UPDATES RIFF |
