-
| .
|
|
|
v1.1418
Code: - added semcboot recovery for MSM8226-based phones ( D2212 Xperia E3, for example ) Procedure is same as for msm8x10-based phones ( signed mode + altbypass, flash firmware ) - small internal changes/fixes
Descargar
|
|
| .
|
-
| .
|
|
|
v1.1419
Code: - added mt6752-based ( E53xx_XPERIA C4 ) flashing - improved msm8994-based phones ( z3+ ) flashing
|
|
| .
|
-
| .
|
|
|
v1.1420
Code: - added mt6795-based ( E56xx_XPERIA M5 ) flashing - added some new models to list for better usability
|
|
| .
|
-
| .
|
|
|
v1.1421
Code: - fixed fatal flaw in mt67xx-based phones flashing ( Xperia_M5 tested personally ) - added workaround for msm8x26-based phones boot repair ( no need to modified APP files )
it was reported by one user, that e56xx_xperia_m5 became dead after successful flashing. please restrain from flashing this phones with setool2, until i'm personally get this phone and test flashing procedure myself.
|
|
| .
|
-
| .
|
|
|
v1.1422
Code: - firmware package will be checked before flashing, flashing does not require temporary files anymore - added msm8928-based phones boot repair ( D51xx_XPERIA T3, etc )
|
|
| .
|
-
| .
|
|
|
v1.1423
Code: - major internal changes in communications routines. Though i'm tested most phone models, there can be errors, so feel free to report any unusual behavior - added msm8230-based phones boot repair - updated s1 loaders
|
|
| .
|
-
| .
|
|
|
v1.1424
- fixed critical error with calypso-based phones, unlock and flash procedures killed phones ( can be repaired by writing eeprom backup )
|
|
| .
|
-
| .
|
|
|
v1.1425
- added support for MSM8996-based phones ( xperia X ) - added support for MT6735-based phones ( xperia E5 ) - added support for MT6755-based phones (xperia XA )
|
|
| .
|
-
| .
|
|
|
v1.1426
- added support for MT6757-based phones (xperia XA1 )
DESCARGA
|
|
| .
|
-
| .
|
|
|
v1.1428
- added support for boot recovery of MT6582,MT6732,MT6735,MT6752,MT6755,MT6795-based phones this is all sony MTK-based models, except G-series
instructions : install latest usbflash drivers ( ggsetup-3.1.0.11.exe ) select proper phone model, add to FW area required firmware, check signed mode + altbypass, press "flash" if phone has damaged boot, just connect phone and press "ready", setool2 will do all other job if phone has damaged security units or "stucked" boot ( no device appears, when phone connected to PC ) - you need to open phone, connect testpoint to GND, connect USB cable to PC, release testpoint and then press "ready"
- added support for boot recovery of MSM8994-based phones this is E58xx, E65xx, E66xx models
|
|
| .
|
-
| .
|
|
|
v1.1429
- added support for boot recovery of MT6589-based phones
|
|
| .
|
-
| .
|
|
|
v1.1430
- added support for MSM8998-based phones ( G81xx,G83xx,G84xx )
|
|
| .
|
101 replies since 19/8/2007, 04:01 9206 views
.